Previous Pics of the Week
1957 Chevrolet Bel Air
Diane Reprogle (Owner)
- 2 Door Hardtop
- Coronado Yellow / White
- 350 Cu-in
- 95% Stock
- Continental Kit
- Chrome Pipes
- Flow Master Mufflers
- Ground up Restoration by L.R. Stevenson of Louisville, KY
- One of a kind Classic Car
1936 Dodge 5 Window Coupe
All Steel Custom Coupe powered by a 396+ Big Block Chevy & Turbo 350 Trans
- Original Body & Chassis
- Mustang II Front End
- Lincoln Versise 9" Rear End
- Disc Front & Rear
- Suicide Doors
- Harris Eng Custom Grill
- Porsche Headlights
- Vintage Air/Heat
- Coolflex Hoses
- Cooling Components Fan
- B&M Trans / Fan Cooler
- Rootlieb Hood & Sides
- SPW Power Windows
- Tea's Seat and Rod Door Panel/Grey Tweed
- Hedman Chrome Headers
- Stainless Steel Exhaust
- Edelbrock SS Mufflers
- Edelbrock 800 Carb, AirGap Polished Intake & Waterpump
- B&M Trans/Fan Cooler
- Mr.Gasket HEI Dist,Wires & Ing Box
- Custom Dash & Console
- 25 Gal SS Gas Tank
- Lokar Shifter,Cables & Pedals
- Ron Francis Wiring
- VDO Gauges
- Centerline "RAZOR" Wheels 15" Fronts & 18" Rear
- Goodyear GTII Radials Tires
1940 Chevy 2dr Sedan
I purchased car May, 2001 with suspension and drive train already in.
Powered by a SB 305 cu.in. Chevy TPI, and geared with a 700R Auto Transmission and a Nova rearend (Drum brakes).
Sprung with a Mustang II front end (disc brakes) and shod with 15 inch American wheels.
Car was white and in need of a lot of work.
Dents, rust, rot, glass and of course paint.
Sept. 2001 I began to take on a project which turned out to be more than I anticipated.
I completed the project Dec. 2002.
All work was done at my brothers body shop, DMZ Auto Body in Bayshore, NY.
I did the majority of work myself, usually 4 to 5 days a week for 5 to 6 hours per day.
What was done:
Builder and Owner: Mike Mancuso Age 55
- Engine Chrome valve covers installed. Cover plate for distributor painted color of car. Radiator stripped and brass polished
- Paint 1985 GM Autumn Maple Firemist PPG DBU color/clear coat Paint was applied by good friend Tony Fronzoni.
- All glass was removed and replaced with bronze tinted safety glass. I had glass cut and installed myself.
- Front and rear fenders were bolted on. They were removed, refurbished and welded back on and molded in. Also the wheel wells were flared with tubing and molded in.
- Hood, center seam, two piece hood welded up and hand fabricated scoops made and installed. Scoops are functional. Nose was shaved of emblems and hood ornament.
- Both doors had to have major repair work on bottoms and hinges had to be made stronger. Top corners of door edges were rounded.
- Roof rust repaired around front and rear windows. Drip rails shaved off.
- Front and rear bumpers removed and bumper/roll pans fabricated with frenched license plate units. Front bumper has turn signal lights.
- Rear 1941 chevy taillights frenched in. Scoops inserted just behind rear wheels. Antenna shaft frenched into top of quarter panel. Also gas filler neck, rear right fender, removed and replaced with smooth contoured hindged lid.
- Trunk Lid Shaved of license plate bracket, lift handle and license plate light. Lid completely smooth and hand fabricated lift handle installed.
- Headlights and signal lights removed from front fenders. Headlights were relocated by moving them outward 5 inches and set down into fenders. Also the tail of the bullet shaped headlight was made 20 inches longer following the curve of the fender. Makes the front of car look wider and the fenders dont look so plain. Headlights were frenched in using kit from Hagans.
- Dash board was stripped, molded in for smooth look and painted the color of the car. The rest of interior is black cloth in good shape and has not been done over yet. All of the window cranks and handles replaced with custom chrome.
Islip Terrace, New York
Custom Ford Coupe
MM@Portland Rodster Show; Portland, OR; Febuary 1997
Here is a car with scallops rather than flames.
Nice, and how about that custom roof line.
This car shows the caliber of show cars that were present.
Of course there were some excellent drivers at the show too!
Check out the archives.
You can also submit your rod by ing me
a scanned photo of your rod or classic car.
Also please include a full description including the following if possible:
model, modifications, engine size, photo credit, owner(s), special features, etc.
This page last updated: